Conversores de Medios de Fibra S-1110HP con Hi-PoE
Conversión de Medios de Fibra y PoE compatible con IEEE 802.3bt

- Cobre 10/100/1000 a Fibra 1G
- Conectores de Fibra Dual SC/ST o de Fibra Simple SC
- Suministra alimentación IEEE 802.3bt Hi-PoE PSE (hasta 100 W)
- Compatible con dispositivos IEEE 802.3af PoE e IEEE 802.3at PoE+ PoE
- Puertos 10/100/1000Base-T PoE dobles o simples
- Funciones avanzadas: PD Reset, Fiber redundancy, Smart Link Pass-Through, Fiber Fault Alert, Auto-MDIX y Loopback
Los Conversores de Medios de Fibra S-1110HP-SFP de Perle conectan de forma transparente el cobre con la fibra y, al mismo tiempo, proporcionan hasta 100 vatios de potencia PSE Hi-PoE compatible con IEEE 802.3bt a dispositivos compatibles con las normas como cámaras de seguridad PTZ con calentadores, iluminación LED en la gestión de edificios y puntos de acceso inalámbricos 802.11ax/ac.
Los Conversores de Medios Hi-PoE de Perle están clasificados como Equipo de Suministro de Energía (PSE). Al usar cables UTP estándar que transportan datos Ethernet, los conversores de medios Hi-PoE de Perle suministran energía a dispositivos alimentados (PD) compatibles con la norma IEEE 802.3bt PoE (hasta 100 W de potencia) o soluciones previas a la norma que incluyen UPoE, 4PPoE, PoE++, UltraPoE, PoE de 4 pares, etc. Como esta norma es totalmente compatible con las normas existentes IEEE 802.3af PoE e IEEE 802.3at PoE+, los PD también serán compatibles. El conversor de medios de fibra S-1110HP cuenta con puertos RJ45 10/100/1000Base-T individuales o duales para alimentar uno o dos PD por conversor Obtenga más información sobre PoE.
Los Conversores de Medios de Fibra S-1110H vienen con puertos de fibra fijos que admiten fibra multimodo o monomodo con conectores dobles ST/SC o conectores de fibra SC de un único hilo.
- extienda la vida útil de equipos no basados en fibra con la transmisión de datos desde dispositivos 10/100/1000Base-T a través de fibra 1000Base-X
- amplíe la distancia de una red existente mediante la conexión de un cable CAT5/6/7 a fibra multimodo o monomodo up to 160km
- proteja los datos de Ethernet del ruido e interferencias electromagnéticas EMI interconectando sus dispositivos de cobre-Ethernet a través de fibra.
Los administradores de redes pueden "verlo todo" con las prestaciones avanzadas de Perle, como Auto-Negotiation, Auto-MDIX, Link Pass-Through, Fiber Fault Alert y Loopbac. Esto permite una mayor eficiencia a la hora de resolver problemas y un menor mantenimiento in-situ. Estas funciones de ahorro de ahorro de costes y tiempo, unidas a la garantía de por vida y el soporte técnico gratuito en todo el mundo, convierten a los conversores de medios PoE S-1110HP de Perle en la elección inteligente para los profesionales de TI.
Los Conversores de Medios PoE S-1110HP-XT también están disponibles con intervalo ampliado de temperaturas de funcionamiento de -40ºC a +75ºC.
Características del Conversor de Medios Hi-PoE S-1110HP
Power Over Ethernet (PSE) | Totalmente compatible con IEEE 802.3bt Tipo 3 y 4 PSE Realiza la función de equipo proveedor de alimentación eléctrica (Power Sourcing Equipment, PSE) en 1 o 2 puertos UTP para dispositivos que cumplen con IEEE 802.3bt. Todos los modelos admiten dispositivos PD de tipo 1 (PoE), tipo 2 (PoE+), tipo 3 (Hi-PoE) y tipo 4 (Hi-PoE) |
Administración avanzada de energía |
|
Restauración de la alimentación del PD | Esta función configurable, idónea para restablecer la alimentación de equipos remotos, realiza un restablecimiento momentáneo de la alimentación del dispositivo alimentado (PD) que se encuentre conectado. Cuando se activa, el conversor de medios, al perder el enlace RX de fibra, desactiva la corriente de salida de PSE hacia el dispositivo PD durante 2 segundos y luego vuelve a activar la alimentación y la mantiene activada hasta que se produzca otra pérdida de enlace RX de fibra (tras su restablecimiento). Cuando se desactiva, la pérdida del enlace RX de fibra no tiene ningún efecto en la alimentación PSE al dispositivo o dispositivos PD. |
Compatibilidad con dispositivos alimentados | PDs Tipo: 1, 2, 3 y 4 PD Clase: 1, 2, 3, 4, 5, 6, 7, 8 Admite ambas conexiones PD de firma simple y dual |
Configuraciones Multipuerto |
|
Correa de alivio de tensión | Incluido con todos los modelos, se proporciona una correa de alivio de tensión para garantizar una conexión de alimentación sólida y segura al convertidor de medios. Ideal para áreas que pueden estar expuestas a vibraciones. |
Auto-Negotiation (802.3u) | El convertidor de medios soporta autonegociación. La interfaz de fibra 1000Base-X negocia según las cláusulas 802.3 37. La 10/100/1000Base-T negocia según las cláusulas 28 y 40 de 802.3. La 1000Base-X se conectará con su compañero una vez que se alcance el máximo común denominador (HCD) Y el cobre se ha vinculado con su socio. El 1000Base-X continuará su ciclo a través de la negociación transmitiendo un fallo remoto de fuera de línea (siempre que esté habilitado a través de la configuración del interruptor) hasta que el cobre esté conectado y los HCD coincidan. El conversor de medios admite la negociación automática de dúplex completo, semidúplex, falla remota, pausa de dúplex completo, pausa asimétrica y Auto MDI-X. |
Auto-MDIX | Auto-MDIX (cruce automático de interfaz dependiente del medio) detecta la señalización de la interfaz Ethernet de cobre para determinar el tipo de cable que se encuentra conectado (de paso directo o de cruce) y configura automáticamente la conexión cuando está activado. El conversor de medios también puede realizar correcciones en el caso de un par en el que se hayan intercambiado los hilos. El conversor de medios se ajustará hasta 120 ns de sesgo de retardo entre los pares 1000Base-T. |
Smart Link Pass-Through | Cuando el interruptor de modo de enlace se coloca en el modo de paso directo de enlace inteligente, el puerto Ethernet de cobre reflejará el estado del puerto del convertidor de medios 1000Base-X. Esta función se puede usar tanto si la negociación automática de fibra está habilitada como si está deshabilitada. |
Alerta de Falla de Fibra | Con Fiber Fault Alert (alerta por fallo de fibra), se informa del estado del receptor 1000Base-X al transmisor 1000Base-X. Esto proporciona notificación de fallos al dispositivo asociado conectado a la interfaz 1000Base-X del conversor de medios. Si el transmisor 1000Base-X está desactivado como resultado de este fallo, se activará periódicamente para permitir que se borre el estado en el caso de que el dispositivo asociado de 1000Base-X utilice una técnica similar. Esto elimina la posibilidad de bloqueos que se produce en algunos conversores de medios. Sólo es aplicable cuando está desactivada la negociación automática. |
Pause (IEEE 802.3xy) | La señalización Pause es una función de IEEE que suspende temporalmente la transmisión de datos entre dos dispositivos en el caso de que uno de ellos esté sobrecargado. El conversor de medios admite la negociación de pausa en la conexión 10/100/1000Base-T y en la conexión de fibra 1000Base-X.
|
Duplex | Se admite funcionamiento dúplex y semidúplex. |
Paquetes Jumbo | Transparente a paquetes jumbo de hasta 10 KB. |
VLAN | Transparente a paquetes con etiqueta de VLAN. |
Remote Loopback | Capacidad para realizar un bucle en la interfaz de fibra 1000Base-X. |
¿No es lo que busca? Vea todos los Conversores de Medios de Fibra de Perle.
¿Necesita ayuda? Contacte con Perle Systems.
Power | |
---|---|
Input Supply Voltage | 52 - 57 vDC |
Power Consumption | 1 x 10/100/1000Base-T port models: 4 watts 2 x 10/100/1000Base-T port models: 4.7 watts Note: for the HP PoE SFP models the numbers above don’t include the SFP power consumptions |
Power Over Ethernet (PSE) | up to 100 watts per port |
Power Connector | 4 pin DIN connector |
![]() |
|
Power Adapter | |
Universal AC/DC adapter | 1 x 10/100/1000Base-T port models: 100-240v AC, regulated AC, 56VDC/120W, 4Pin DIN connector (adapter included) 2 x 10/100/1000Base-T port models: 100-240v AC, regulated AC, 56VDC/200W, 4Pin DIN connector (adapter included) |
Indicators | |
Power (PWR) | This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink slowly when either fiber port is in Loopback test mode. The LED will blink quickly if there is a hardware failure where the reason code can be identified through a combination of FDF,LKF, FDC and PSE indicator LEDs |
Fiber link on / Receive activity (LKF 1/2) |
This green LED is operational only when power is applied. The LED will blink along with transmit/receive data on the fiber port If a loss of link on the copper port results in a Link Passthrough condition to the fiber port, this LED will blink at a rate of once every 2 seconds until the condition is cleared. |
Copper link on / Receive activity (LKC 1/2) |
This green LED is operational only when power is applied. The LED will blink along with transmit/receive data on the 10/100/1000 UTP port If a loss of link on the copper port results in a Link Passthrough condition to the fiber port, this LED will blink at a rate of once every 2 seconds until the condition is cleared. |
Fiber Duplex (FDF 1/2) |
This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-X link is operational in full duplex mode. The LED is off when in half duplex. If the Auto-Neg switch is turned off, this LED will always be on |
Copper Duplex (FDC 1/2) |
This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-T link is operational in full duplex mode. The LED is off when in half duplex |
100/1000 | This multi-color LED is operational only when power is applied. The LED is green when the speed of the copper ethernet port is running at 1000 Mbps. The LED is yellow when the speed of the copper Ethernet port is running at 100 Mbps. The LED is off when in 10 Mbps. |
PSE Status (PSE 1/2) |
This LED will signify the status of the PSE function. Using multi-color and blinking the unit will show the following status for the PSE; GREEN — Solid: The PSE has successfully detected a compliant PD and is applying power over the UTP (for legacy pin out simply show active power when applied) YELLOW — Solid: The PSE is not active. This means the PSE has been configured to provide power, but the PD is :
OFF — PSE function switch disabled RED — Blinking: Error Conditions
|
Switches - accessible through a side opening in the chassis | |
![]() |
|
Auto-Negotiation (802.3u) | Enabled (Default) - The media converter uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex, half duplex, pause and remote fault capabilities.
Disabled - The media converter sets the port according to the position of the speed and duplex switches. |
Link Mode | Link Mode provides a transparency to the state of the copper link allowing for simplified trouble shooting from the devices connected to the media converter. Normal (Default — Up) With Fiber Auto Negotiation disabled the state of the copper link has no effect on the 1000Base-X link. Smart Link Pass Through (Down) With Fiber Auto-Negotiation disabled the behavior is as follows. When the copper receiver is off the 1000Base-X transmitter will be turned off. When the 1000Base-X receiver goes off the copper transmitter will be turned off. |
Fiber Fault Alert | The Fiber Fault Alert switch has meaning when Auto-Negotiation is disabled Enabled (Default - Up) Disabled (Down) |
Loopback | The media converter can perform a loopback on the 1000Base-X fiber interface. Disabled (Default - Up) Enabled - The 1000Base-X receiver is looped to the 1000Base-X transmitter. The copper transmitter is taken off the interface. |
Speed Copper | 100 (Default) 10 |
Duplex Copper | Full (Default) Half |
Fiber Negotiation | Up: The Media Converter will negotiate Ethernet parameters on the fiber connection. This will ensure that the most optimal connection parameters will be in effect. If connecting to another Perle Media Converter, this parameter should be set to Auto. The Media Converter Module will advertise 1000Mbps, Full and Half Duplex, no Pause. Down: The Media Converter Module’s fiber will be fixed to 1000Mbps, Full Duplex. |
Auto-MDIX (Internal Strap) |
If Auto-Negotiation (802.3u) is enabled, the media converter determines the current cable pinout to use on the copper interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the copper interface to set the port MDI or MDIX whichever is appropriate. Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable. Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media converter's transmitter and the partner devices transmitter are connected to the others receiver. The Media converter's 100Base-TX port is configured as MDI-X with this switch setting. |
PSE Power | Settable for each UTP port available. When enabled (UP), the media converter will perform a Power Sourcing Equipment (PSE) function as per IEEE802.3bt standard. Default is "enabled" |
PD Power Reset | This is a technique to perform a power reset on a PD device(s) attached. When enabled (down), the media converter will upon loss of link on any fiber port, turn off PSE output power to the PD device(s) for 2 seconds then turn the power back on. The power remains on until any fiber link transitions from up to down again. With Passthrough enabled (Link Mode enabled and Fiber Auto-Negotiation enabled) , a loss of link on the fiber resulting from a loss of link on the copper, a PD Power Reset till still occur. When PD Power Reset disabled, loss of fiber link has no effect on PSE power to the PD device(s). |
PoE power vs Ethernet CAT | CAT3 and above for PoE power up to 15.4 watts CAT5 and above for PoE power between 15.4 watts and up to 30 watts CAT6 and above for PoE power between 30 watts and up to 100 watts Note: always choose the highest Ethernet CAT category between desired speed and PoE power |
Connectors | |
10/100/1000Base-T | RJ45 connector 2 pair CAT5, EIA/TIA 568A/B or better cable for 10/100. 4 pair CAT5 UTP cable for Gigabit. Note: always choose the highest Ethernet CAT category between desired speed and PoE power |
Magnetic Isolation | 1.5kv |
Fixed Fiber | Dual multimode or single mode (Duplex) fiber - SC, ST Single strand fiber (Simplex) - SC |
Small Form Factor Pluggable (SFP) slot |
SFP slot models: Empty slot for 1000Base-X or 100Base-X SFP modules supplied by Perle, Cisco or other manufacturers of MSA compliant SFPs. Hot insertion and removable (hot swappable). |
Filtering | |
Filtering | 1024 MAC Addresses |
Frame Specifications | |
Buffer | 1000 Kbits frame buffer memory |
Size | Maximum frame size of 10,240 bytes -- Gigabit Maximum frame size of 2048 bytes -- Fast Ethernet |
Environmental Specifications | |
Operating Temperature | 0 C to 50 C (32 F to 122 F) |
Storage Temperature | minimum range of -25 C to 70 C (-13 F to 158 F) |
Operating Humidity | 5% to 90% non-condensing |
Storage Humidity | 5% to 95% non-condensing |
Operating Altitude | Up to 3,048 meters (10,000 feet) |
Heat Output (BTU/HR) |
1 x 10/100/1000Base-T port models: 13.65 BTU/hr 2 x 10/100/1000Base-T port models: 16 BTU/hr |
MTBF (Hours)* | 342019 |
Chassis | Metal with an IP20 ingress protection rating |
Mounting | |
Din Rail Kit | Optional |
Rack Mount Kit | Optional |
Product Weight and Dimensions | |
Weight | 0.4 Kg, 1.0 lbs (no power adaptor) |
Dimensions | 150 x 95 x 26 mm, 5.9 x 3.7 x 1.0 inches |
Packaging | |
Shipping Weight | 1.36 kg, 3 lbs |
Shipping Dimensions | 300 x 200 x 70 mm, 11.81 x 7.87 x 2.75 inches |
Regulatory Approvals | |
Emissions | FCC Part 15 Class A, EN55022 Class A |
CISPR 22 Class A CISPR 32:2012/EN 55032:2012 (Class A) CISPR 24:2010/EN 55024:2010 |
|
EN61000-3-2 | |
Immunity | EN55024 |
Electrical Safety | IEC 62368-1(ed 2) EN 62368-1:2014 |
CE | |
Environmental | Reach, RoHS and WEEE Compliant |
Other | ECCN: 5A991 |
HTSUS Number: 8517.62.0020 | |
Perle Limited Lifetime Warranty |
*Calculation model based on MIL-HDBK-217-FN2 @ 30 °C
Select a Model to obtain a Part Number - S-1110HP Hi-PoE+
Model | # PoE ports |
Fiber Port Connector |
Type | Transmit (dBm) |
Receive (dBm) |
Power Budget (dBm) |
Wavelength (nm) |
Fiber Type |
Core Size (um) |
Modal Bandwidth (MHz*Km) |
Operating Distance |
||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Min | Max | Min | Max | ||||||||||
S-1110HP-SC05 | 1 | Dual SC |
1000Base-SX |
-9.5 |
-4.0 |
-17 |
-3.0 |
7.5 |
850 |
MMF |
62.5 |
160 |
220 m (722 ft) |
62.5 |
200 |
275 m (902 ft) |
|||||||||||
50 |
400 |
500 m (1,640 ft) |
|||||||||||
50 |
500 |
550 m (1,804 ft) |
|||||||||||
50 |
2000 |
1000 m (3281 ft) |
|||||||||||
S-1110HP-ST05 | 1 | Dual ST |
1000Base-SX |
-9.5 |
-4.0 |
-17 |
-3.0 |
7.5 |
850 |
MMF |
62.5 |
160 |
220 m (722 ft) |
62.5 |
200 |
275 m (902 ft) |
|||||||||||
50 |
400 |
500 m (1,640 ft) |
|||||||||||
50 |
500 |
550 m (1,804 ft) |
|||||||||||
50 |
2000 |
1000 m (3281 ft) |
|||||||||||
1 | Dual SC |
1000Base-LX |
-6.0 |
0.0 |
0.0 |
-17.0 |
6.0 |
1310 |
MMF |
62.5 |
160 |
2 km (1.2 mi) |
|
50 |
500 |
1000m (3280 ft) |
|||||||||||
1 | Dual ST |
1000Base-LX |
-6.0 |
0.0 |
0.0 |
-17.0 |
6.0 |
1310 |
MMF |
62.5 |
160 |
2 km (1.2 mi) |
|
50 |
500 |
1000m (3280 ft) |
|||||||||||
S-1110HP-SC10 | 1 | Dual SC |
1000Base-LX/LH |
-9.5 |
-3.0 |
-20 |
-3.0 |
10.5 |
1310 |
MMF* |
62.5 |
500 |
1000 m (3281 ft) |
50 |
400 |
550 m (1,804 ft) |
|||||||||||
50 |
400 |
550 m (1,804 ft) |
|||||||||||
SMF |
** |
- |
10 km (6.2 mi) |
||||||||||
S-1110HP-ST10 | 1 | Dual ST |
1000Base-LX/LH |
-9.5 |
-3.0 |
-20 |
-3.0 |
10.5 |
1310 |
MMF* |
62.5 |
500 |
550 m (1,804 ft) |
50 |
400 |
550 m (1,804 ft) |
|||||||||||
50 |
400 |
550 m (1,804 ft) |
|||||||||||
SMF |
** |
- |
10 km (6.2 mi) |
||||||||||
S-1110HP-SC40 | 1 | Dual SC |
1000Base-EX |
-2.0 |
2.0 |
-23 |
-3.0 |
21 |
1310 |
SMF |
** |
- |
40 km (25 mi) |
S-1110HP-ST40 | 1 | Dual ST |
1000Base-EX |
-2.0 |
2.0 |
-23 |
-3.0 |
21 |
1310 |
SMF |
** |
- |
40 km (25 mi) |
S-1110HP-SC70 | 1 | Dual SC |
1000Base-ZX |
-2.0 |
5.0 |
-23 |
-3.0 |
21 |
1550 |
SMF |
- |
- |
70 km (43 mi) |
S-1110HP-ST70 | 1 | Dual ST |
1000Base-ZX |
-2.0 |
5.0 |
-23 |
-3.0 |
21 |
1550 |
SMF |
- |
- |
70 km (43 mi) |
S-1110HP-SC120 | 1 | Dual SC |
1000Base-ZX |
0.0 |
5.0 |
-32.0 |
-9.0 |
32 |
1550 |
SMF |
- |
- |
120 km (75 mi) |
S-1110HP-ST120 | 1 | Dual ST |
1000Base-ZX |
0.0 |
5.0 |
-32.0 |
-9.0 |
32 |
1550 |
SMF |
- |
- |
120 km (75 mi) |
S-1110HP-SC160 | 1 | Dual SC |
1000Base-ZX |
2.0 |
5.0 |
-32.0 |
-9.0 |
34 |
1550 |
SMF |
- |
- |
160 km (100 mi) |
S-1110HP-ST160 | 1 | Dual ST |
1000Base-ZX |
2.0 |
5.0 |
-32.0 |
-9.0 |
34 |
1550 |
SMF |
- |
- |
160 km (100 mi) |
S-1110DHP-SC05 | 2 | Dual SC |
1000Base-SX |
-9.5 |
-4.0 |
-17 |
-3.0 |
7.5 |
850 |
MMF |
62.5 |
160 |
220 m (722 ft) |
62.5 |
200 |
275 m (902 ft) |
|||||||||||
50 |
400 |
500 m (1,640 ft) |
|||||||||||
50 |
500 |
550 m (1,804 ft) |
|||||||||||
50 |
2000 |
1000 m (3281 ft) |
|||||||||||
S-1110DHP-ST05 | 2 | Dual ST |
1000Base-SX |
-9.5 |
-4.0 |
-17 |
-3.0 |
7.5 |
850 |
MMF |
62.5 |
160 |
220 m (722 ft) |
62.5 |
200 |
275 m (902 ft) |
|||||||||||
50 |
400 |
500 m (1,640 ft) |
|||||||||||
50 |
500 |
550 m (1,804 ft) |
|||||||||||
50 |
2000 |
1000 m (3281 ft) |
|||||||||||
2 | Dual SC |
1000Base-LX |
-6.0 |
0.0 |
0.0 |
-17.0 |
6.0 |
1310 |
MMF |
62.5 |
160 |
2 km (1.2 mi) |
|
50 |
500 |
1000m (3280 ft) |
|||||||||||
2 | Dual ST |
1000Base-LX |
-6.0 |
0.0 |
0.0 |
-17.0 |
6.0 |
1310 |
MMF |
62.5 |
160 |
2 km (1.2 mi) |
|
50 |
500 |
1000m (3280 ft) |
|||||||||||
S-1110DHP-SC10 | 2 | Dual SC |
1000Base-LX/LH |
-9.5 |
-3.0 |
-20 |
-3.0 |
10.5 |
1310 |
MMF* |
62.5 |
500 |
550 m (1,804 ft) |
50 |
400 |
550 m (1,804 ft) |
|||||||||||
50 |
400 |
550 m (1,804 ft) |
|||||||||||
SMF |
** |
- |
10 km (6.2 mi) |
||||||||||
S-1110DHP-ST10 | 2 | Dual ST |
1000Base-LX/LH |
-9.5 |
-3.0 |
-20 |
-3.0 |
10.5 |
1310 |
MMF* |
62.5 |
500 |
550 m (1,804 ft) |
50 |
400 |
550 m (1,804 ft) |
|||||||||||
50 |
400 |
550 m (1,804 ft) |
|||||||||||
SMF |
** |
- |
10 km (6.2 mi) |
||||||||||
S-1110DHP-SC40 | 2 | Dual SC |
1000Base-EX |
-2.0 |
2.0 |
-23 |
-3.0 |
21 |
1310 |
SMF |
** |
- |
40 km (25 mi) |
S-1110DHP-ST40 | 2 | Dual ST |
1000Base-EX |
-2.0 |
2.0 |
-23 |
-3.0 |
21 |
1310 |
SMF |
** |
- |
40 km (25 mi) |
S-1110DHP-SC70 | 2 | Dual SC |
1000Base-ZX |
-2.0 |
5.0 |
-23 |
-3.0 |
21 |
1550 |
SMF |
- |
- |
70 km (43 mi) |
S-1110DHP-ST70 | 2 | Dual ST |
1000Base-ZX |
-2.0 |
5.0 |
-23 |
-3.0 |
21 |
1550 |
SMF |
- |
- |
70 km (43 mi) |
S-1110DHP-SC120 | 2 | Dual SC |
1000Base-ZX |
0.0 |
5.0 |
-32 |
-9.0 |
32 |
1550 |
SMF |
- |
- |
120 km (75 mi) |
S-1110DHP-ST120 | 2 | Dual ST |
1000Base-ZX |
0.0 |
5.0 |
-32 |
-9.0 |
32 |
1550 |
SMF |
- |
- |
120 km (75 mi) |
S-1110DHP-SC160 | 2 | Dual SC |
1000Base-ZX |
2.0 |
5.0 |
-32 |
-9.0 |
34 |
1550 |
SMF |
- |
- |
160 km (100 mi) |
S-1110DHP-ST160 | 2 | Dual ST |
1000Base-ZX |
2.0 |
5.0 |
-32 |
-9.0 |
34 |
1550 |
SMF |
- |
- |
160 km (100 mi) |
Single Fiber Models Recommended use in pairs
Model | # PoE ports | Connector | Type | Transmit (dBm) |
Receive (dBm) |
Power Budget (dBm) |
Wavelength (nm) |
Fiber Type |
Core Size (um) |
Modal Bandwidth (MHz* Km) |
Operating Distance |
||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Min | Max | Min | Max | ||||||||||
1 | Single SC |
1000Base-BX-U |
-10.0 |
-4.0 |
-17.0 |
-3.0 |
7.0 |
1310 / 1550 |
MMF |
62.5 |
500 |
500 m (1,640 ft) |
|
50 |
500 |
500 m (1,640 ft) |
|||||||||||
1 | Single SC |
1000Base-BX-D |
-10.0 |
-4.0 |
-17.0 |
-3.0 |
7.0 |
1550 / 1310 |
MMF |
62.5 |
500 |
500 m (1,640 ft) |
|
50 |
500 |
500 m (1,640 ft) |
|||||||||||
S-1110HP-SC10U | 1 | Single SC |
1000Base-BX-U |
-9.0 |
-3.0 |
-20 |
-3.0 |
11 |
1310 / 1490 |
SMF |
** |
- |
10 km (6.2 mi) |
S-1110HP-SC10D | 1 | Single SC |
1000Base-BX-D |
-9.0 |
-3.0 |
-20 |
-3.0 |
11 |
1490 / 1310 |
SMF |
** |
- |
10 km (6.2 mi) |
S-1110HP-SC20U | 1 | Single SC |
1000Base-BX-U |
-8.0 |
-3.0 |
-22 |
-3.0 |
14 |
1310 / 1490 |
SMF |
** |
- |
20 km (12.4 mi) |
S-1110HP-SC20D | 1 | Single SC |
1000Base-BX-D |
-8.0 |
-3.0 |
-22 |
-3.0 |
14 |
1490 / 1310 |
SMF |
** |
- |
20 km (12.4 mi) |
S-1110HP-SC40U | 1 | Single SC |
1000Base-BX-U |
-3.0 |
2.0 |
-23 |
-3.0 |
20 |
1310 / 1490 |
SMF |
** |
- |
40 km (25 mi) |
S-1110HP-SC40D | 1 | Single SC |
1000Base-BX-D |
-3.0 |
2.0 |
-23 |
-3.0 |
20 |
1490 / 1310 |
SMF |
** |
- |
40 km (25 mi) |
S-1110HP-SC80U | 1 | Single SC |
1000Base-BX-U |
-2.0 |
3.0 |
-26 |
-3.0 |
24 |
1510 / 1590 |
SMF |
- |
- |
80 km (50 mi) |
S-1110HP-SC80D | 1 | Single SC |
1000Base-BX-D |
-2.0 |
3.0 |
-26 |
-3.0 |
24 |
1590 / 1510 |
SMF |
- |
- |
80 km (50 mi) |
S-1110HP-SC120U | 1 | Single SC |
1000Base-BX-U |
-3.0 |
2.0 |
-34 |
-9.0 |
31 |
1510 / 1590 |
SMF |
- |
- |
120 km (75 mi) |
S-1110HP-SC120D | 1 | Single SC |
1000Base-BX-D |
-3.0 |
2.0 |
-34 |
-9.0 |
31 |
1590 / 1510 |
SMF |
- |
- |
120 km (75 mi) |
2 | Single SC |
1000Base-BX-U |
-10.0 |
-4.0 |
-17.0 |
-3.0 |
7.0 |
1310 / 1550 |
MMF |
62.5 |
500 |
500 m (1,640 ft) |
|
50 |
500 |
500 m (1,640 ft) |
|||||||||||
2 | Single SC |
1000Base-BX-D |
-10.0 |
-4.0 |
-17.0 |
-3.0 |
7.0 |
1550 / 1310 |
MMF |
62.5 |
500 |
500 m (1,640 ft) |
|
50 |
500 |
500 m (1,640 ft) |
|||||||||||
S-1110DHP-SC10U | 2 | Single SC |
1000Base-BX-U |
-9.0 |
-3.0 |
-20 |
-3.0 |
11 |
1310 / 1490 |
SMF |
** |
- |
10 km (6.2 mi) |
S-1110DHP-SC10D | 2 | Single SC |
1000Base-BX-D |
-9.0 |
-3.0 |
-20 |
-3.0 |
11 |
1490 / 1310 |
SMF |
** |
- |
10 km (6.2 mi) |
S-1110DHP-SC20U | 2 | Single SC |
1000Base-BX-U |
-8.0 |
-3.0 |
-22 |
-3.0 |
14 |
1310 / 1490 |
SMF |
** |
- |
20 km (12.4 mi) |
S-1110DHP-SC20D | 2 | Single SC |
1000Base-BX-D |
-8.0 |
-3.0 |
-22 |
-3.0 |
14 |
1490 / 1310 |
SMF |
** |
- |
20 km (12.4 mi) |
S-1110DHP-SC40U | 2 | Single SC |
1000Base-BX-U |
-3.0 |
2.0 |
-23 |
-3.0 |
20 |
1310 / 1490 |
SMF |
** |
- |
40 km (25 mi) |
S-1110DHP-SC40D | 2 | Single SC |
1000Base-BX-D |
-3.0 |
2.0 |
-23 |
-3.0 |
20 |
1490 / 1310 |
SMF |
** |
- |
40 km (25 mi) |
S-1110DHP-SC80U | 2 | Single SC |
1000Base-BX-U |
-2.0 |
3.0 |
-26 |
-3.0 |
24 |
1510 / 1590 |
SMF |
- |
- |
80 km (50 mi) |
S-1110DHP-SC80D | 2 | Single SC |
1000Base-BX-D |
-2.0 |
3.0 |
-26 |
-3.0 |
24 |
1590 / 1510 |
SMF |
- |
- |
80 km (50 mi) |
S-1110DHP-SC120U | 2 | Single SC |
1000Base-BX-U |
-3.0 |
2.0 |
-34 |
-9.0 |
31 |
1510 / 1590 |
SMF |
- |
- |
120 km (75 mi) |
S-1110DHP-SC120D | 2 | Single SC |
1000Base-BX-D |
-3.0 |
2.0 |
-34 |
-9.0 |
31 |
1590 / 1510 |
SMF |
- |
- |
120 km (75 mi) |
The minimum fiber cable distance for all converters listed is 2 meters.
*A mode-conditioning adapter as specified by the IEEE standard, is required regardless of the span length. Note how the mode conditioning adapter for 62.5-um fibers has a different specification from the mode-conditioning adapter for 50-um fibers.
**ITU-T G.652 SMF as specified by the IEEE 802.3z standard.
Media Converter Accessories | |
---|---|
4 DIN Rail Mount Bkt | DIN Rail Mounting Kit |
MCSM | Standalone media converter wall mount bracket |